12.Remove pellets from the hopper; disconnect metering motor to determine if HRD is spinning freely. The fan turns but the auger is not turning. If your Harman Stove has stopped feeding pellets, there could be a few simple solutions: The front door, ash pan door or hopper lid may not be closed properly. Pellet Stove Starts Up But Randomly Shuts Down. All England's stove works pellet units use a two auger feed system. I have seen stoves that passed the factory's quality control without a bottom auger bearing present! If the auger motor turns, check to see if the auger is slipping, jammed or damaged. If the pellet stove is not burning efficiently or producing suitable quantities of heat, the problem could be a result of air leaks through the door seals. The number of pellets will always be the minimum required to keep the flame small but exceedingly hot. Checked vacuum switch and it appears fine, cleaned stove thoroughly (on top of regular weekly cleanings). The auger was corroded & froze up. It did its thing with the auto-light and everything was fine for about five minutes. Also, your pellets might not being feeding into the auger correctly, due to … Contractor's Assistant: Do you know the model of your Drolet pellet stove? Auger jamming / stove shutting down: Long pellets: Drop bags on the floor – this can break long pellets … My drolet pellet stove is not working. In the case of Englander stoves with dual augers, the switch is only connected to the top auger which also stops the pellets from feeding and shuts the stove down. Push Auger Followed the start up instructions in the manual and everything works as should until the auger is supposed to start turning. They need not be replaced if they are sticking or jamming. Best pellet stove of 2018. They just needs a thorough cleaning to remove gummy deposits. In this regard, how often should you clean your pellet stove pipe? Venting may be blocked. The upper auger located at the bottom of the hopper runs intermittently. NOTE: Turning the ON/OFF Switch to ”OFF” does not disconnect all power to the electrical components of the stove. How old is it? To clean a pellet stove in a proper way, you have to make a routine during the heavy running period of a pellet stove. Meter Motor Turning (HRD)? Wiggle the auger motor away and set it aside. i've had this happen once before and replaced the auger and it was fine. Just bought the house 2 months ago and this is the only source of heat. NOTE: Do not use a wrench or socket drive on 7/16” retaining bolt on HRD to free a jam. PRIMING THE AUGER. Whitfield pellet stoves use a pressure switch to sense if there is sufficient combustion air flow. Stove seems to run fine for a while, and then top auger stops turning and fire goes out. Oil the motor, if needed. • Do not operate your stove with the viewing door open. Use a 5/32 allen wrench to loosen the lower set screw on the coupling between the auger motor shaft and the shaft of the auger. After that time, I realized that the fire that had started was getting smaller. Harman Pellet Stove P38 Auger Not Turning. The fuse looks good. The heating appliance is sure to perform poorly if poor grade of pellets are used as fuel. I have a variety of material used in the construction of pellet stove including metal, plastic, and glass. • Never try to repair or replace any part of the stove unless instructions for doing so are given in this manual. Hudson River Stove Works Davenport Pellet Stove and Insert; Hudson River Stove Works ChathamPellet Stove and Insert; Part Description: This 1RPM auger motor has a 3/8″ diamater x 1 1/8″ shaft and pushes pellet fuel from the hopper to the burn pot. Fill the hopper and allow a few minutes for the unit to auger the pellets onto the burn pot. Auger bearings hold the pellet stove auger in place. Whole, charred pellets left in the burn pot: Air-to-pellet ratio: Adjust air-to-pellet ratio by decreasing air flow and/or decreasing feed rate. Serious damage can occur or bolt can be broken. Adjust air-to-pellet ratio by decreasing air flow and/or decreasing feed rate. Because the pellet stove sat in a barn for so long it was exposed to some moisture. First things first: If your pellet stove is blowing cold air, make sure the heat setting is not on low. As for age of the motors I have no idea. Take a look at the door seal and make sure it closes with a perfect fit to eliminate air leaks. Use High-Quality Pellets. The auger is not turning. • Never try to repair or replace any part of the stove unless instructions for doing so are given in this manual. So it sounds as though the problem is that the upper auger is not feeding pellets to the lower auger. If you have questions about your auger or it’s not functioning as it should, you have some very good online resources for getting all your questions answered about your Magnum pellet stove. Step 7 Turn the feed adjustment knob to zero, wait two minutes and press the "Shut Down" button if all troubleshooting steps fail to start the auger motor. However, after giving you the TOP list, I will also give you some of the benefits you stand to gains for using it. My Stove Keeps Shutting Down You may have noticed the common causes for most pellet stove problems by now – a dirty unit, and poor air adjustment which won't provide enough heat to trip the sensors. Make sure you're not adding too many pellets as well as getting enough air flow into the stove. The stove has been running now for a good 30 min with no problem. Leading up the the auger not turning at all, it sounded like it was slowly dying. It seems like when the top auger stops working, if I press the start button again it runs fine. It appeared that the lower auger wasn’t turning. How can I tell if the vacuum switch is on and how do I "jump" the vacuum and snap disc 1 to run the diagnostic test? The hopper may be empty. Normally, the convection fan starts operating, and then the pressure switch will close sending power to the auger motor, which starts feeding pellets. • Do not operate your stove with the viewing door open.